Wood Style Skier Parts
-
NordicTrack Skier Maintenance Kit
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
NordicTrack skier maintenance kit comes with a bottle of 3inOne oil, a bar of paraffin wax, a piece of emery cloth and a piece of scotchbrite pad.
-
3inOne Oil
Free Shipping for orders over $50 within the USA
The only lubrication that should be used on your NordicTrack is 3inOne Oil. Lube the wheels that spin freely at the front and back of the skier, lube the leather pad that sits under the arm cord drum, lube the bearing that sits on top of the arm cord drum. DO NOT LUBRICATE THE DRIVEROLLERS. -
Paraffin Wax
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
Paraffin wax is used to coat the sides of the skis so they have wood on wood lubrication. It's important to coat the sides of the skis every 3 months with paraffin wax as it will help reduce the friction that is caused from wood on wood contact.
We sell it in a 1.25 x 2.5 inch bar.
-
Driveroller Set Wood Style Skier
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
If your NordicTrack skier is slipping you need to replace the driverollers. The driverollers are the two rollers located in the center of the machine near the flywheel.
These driverollers are new and will fit any wood style skier built from 1976 to 1999 and NordicSport skiers that used a metal flywheel and dragstrap. Two come in a set. For best results, purchase this set. These driverollers are manufactured in the US by NordicParts.
These driverollers are 2.355 inches in height.
We include detailed installation instructions and it is simple to install the driverollers. Remove the skis, tip the skier on its side, remove the two #3 phillips screws and the four 1/2 bolts located on the wooden side board, once you remove the side board the driveroller will slide off the flywheel axle, then wipe the flywheel axle off with a paper towel soaked in rubbing alcohol, then install the new driveroller so it spins freely forward and locks in the back stroke, then re-install the sideboard and repeat these steps to the other side. Its easier to do one side at a time. NEVER LUBRICATE the driverollers as this could cause the one-way roller clutch bearing inside of them to slip.
If your NordicTrack skier is slipping in the back stroke then these rollers are what you need to repair your ski machine.
Replacing the driverollers is very easy. Just make sure you install the replacement rollers so they both spin freely forward and lock in the back stroke.
The driverollers we sell are manufactured from the original company who supplied them to NordicTrack in the 80's and 90's. In fact, we own the original mold and these are only produced for NordicParts.com.
If you have a ICON skier which would have been produced after 1999 then please contact us prior to ordering.
-
One Driveroller
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The driverollers are the two rollers located in the center of the machine near the flywheel.
The price for a single driveroller is $59.50. We do include very detailed installation instructions and it is simple to install the driverollers. Remove the skis, tip the skier on its side, remove the two #3 phillips screws and the four 1/2 bolts located on the wooden side board, once you remove the side board the driveroller will slide off the flywheel axle, then wipe the flywheel axle off with a paper towel soaked in rubbing alcohol, then install the new driveroller so it spins freely forward and locks in the back stroke, then re-install the sideboard and repeat these steps to the other side. Its easier to do one side at a time. NEVER EVER LUBRICATE the driverollers this could cause the one-way roller clutch bearing inside of them to slip.
If your NordicTrack skier is slipping in the back stroke then these rollers are what you need to repair your ski machine.
Replacing the driverollers is very easy. Just make sure you install the replacement rollers so they both spin freely forward and lock in the back stroke.
The driverollers we sell are manufactured from the original company who supplied them to NordicTrack in the 80's and 90's. In fact, we own the original mold and these are only produced for NordicParts.com.
-
Driveroller Set, Flywheel Axle and Side Board Bearings
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
This set will fit all original USA built skiers that were produced from 1976 to 1998 and it will also allow you to convert the ICON Classic Pro Skier which was produced from 1999 to present to the original USA manufactured skiers specs.
Icon Health and Fitness had purchased the NordicTrack name in 1999. Around 2004 ICON changed the dimensions of the flywheel axle, side board bearings and the inside diameter of the driverollers so the original design of the driverollers will not fit there current ski machines. Icon also didn't harden the flywheel axle to the level that they should have so its very common for an Icon Classic Pro skier to have its driverollers fuse to the flywheel axle. With this kit you will improve any ICON skier to work like the original USA built ones from the 1980's and the 1990's
If you do have a wood style skier from the 80's and 90's this combo will ensure a smooth action and it is the exact parts that would have come on your skier.
If your NordicTrack skier is slipping in the back stroke then these rollers are what you need to repair your ski machine.
Replacing the driverollers is very easy. Just make sure you install the replacement rollers so they both spin freely forward and lock in the back stroke.
The driverollers we sell are manufactured from the original company who supplied them to NordicTrack in the 80's and 90's. In fact, we own the original mold and these are only produced for NordicParts.com.
This combo includes, 2 New Driverollers, Flywheel Axle and 2 Side Board Bearings.
-
Honey Comb Style Driveroller Set
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
This set of driverollers is the honey comb style. The driverollers are the two rollers located in the center of the NordicTrack. If your skier feels like it is slipping you will need to replace the driverollers. The honey comb driverollers were on most of the skiers from 1995 to 1998. This set comes with 2 new driverollers. We do include very detailed installation instructions and it is simple to install the driverollers. Remove the skis, tip the skier on its side, remove the two #3 phillips screws and the four 1/2 bolts located on the wooden side board, once you remove the side board the driveroller will slide off the flywheel axle, then wipe the flywheel axle off with a paper towel soaked in rubbing alcohol, then install the new driveroller so it spins freely forward and locks in the back stroke, then re-install the sideboard and repeat these steps to the other side. Its easier to do one side at a time. NEVER EVER LUBRICATE the driverollers this could cause the one-way roller clutch bearing inside of them to slip.
If your NordicTrack skier is slipping in the back stroke then these rollers are what you need to repair your ski machine.
Replacing the driverollers is very easy. Just make sure you install the replacement rollers so they both spin freely forward and lock in the back stroke.
The driverollers we sell are manufactured from the original company who supplied them to NordicTrack in the 80's and 90's. In fact, we own the original mold and these are only produced for NordicParts.com.
-
One Honey Comb Driveroller
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
This is for one Honey Comb style driveroller. This style of driveroller came on most of the wood style skiers from 1995 to 1998. If your skier feels like it is slipping that means the driveroller has worn out. For best results purchase a set. They are also listed separately on this site.
If your NordicTrack skier is slipping in the back stroke then these rollers are what you need to repair your ski machine.
Replacing the driverollers is very easy. Just make sure you install the replacement rollers so they both spin freely forward and lock in the back stroke.
The driverollers we sell are manufactured from the original company who supplied them to NordicTrack in the 80's and 90's. In fact, we own the original mold and these are only produced for NordicParts.com.
-
End Roller Set (used)
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
We are currently out of stock of NEW Plastic, hollow style endroller. The manufacturer who produces them is having a huge delay and does not know when they will be able to produce them. We do have used enrollers in stock that are in great condition or there is a better option for endrollers. I always recommend to my customers to convert their skier over to the double 8 endroller style and to add the spacers. We do have the double style in stock so if you need endrollers please choose this option.
The End Rollers are the four rollers that spin freely. Two are located in the front and two are located in the rear. Four come in a set. Skiers manufactured in the 70's and most of the 80's had 8 endrollers.
We have the narrower end rollers as well which are also listed on the site. If your skier was made in the 80's you most likely have 8 endrollers and will need the narrower ones. If you do have 8 endrollers these larger ones will not fit your 80's wood style skier.
The axle for the endrollers need to be lubricated with 3inOne oil when you first install the endrollers and every three months there after.
-
Smaller Solid Endroller
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The smaller soild endroller was used on the skiers manufactured in the 1970's through the late 1980's. There were a total of 8 endrollers. The smaller solid endrollers are located at the front and the back of the NordicTrack. The endroller axles need to be lubricated with 3inOne oil every couple months to help prolong the life of the bushing inside of them and to keep your NordicTrack quit.
These wheels measure 3/4 inch wide by 2 inches high and the hole in the center is 1/4 inch.
-
Pro Drag Strap Spring
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The spring is connected to the front frame and the drag strap. This spring will only fit: Pro, Excel, Challenger, Sequoia, 505, 530, Easy ski, Limited. If you have an Achiever, Medalist or Elite skier this spring WILL NOT FIT we do however have the dragstrap spring for the Achievers, Medalists and Elites under the 30 LBS spring set on the site.
-
Arm Exerciser Cord
Free Shipping for orders over $50 within the USA
Cord is 171 inches in length. Fits all wooden style skiers, NordicSport, and Club models. Plus series skiers use a special Kevlar cord, please shop in the plus series section if you have a Plus series.
It is very simple to install the arm cord. You need to untie the cord inside of the grips, or you can cut the old cord, remove the knob, spring, bearing assembly, then lift the drum assembly off the skier, flip it over and unscrew the four screws, then lift the metal plate off. At that point you will see two notches in the drum, pull the old cord out and put the new cord in those notches. Then pull the cord so both ends are even and then put the metal plate back on. You may want to use a little dab of Elmer’s glue on the thread of the screws as this helps them from coming loose. Now wrap one end of the cord 2.5 times to the left and then wrap the other end of the cord 2.5 times to the right. Make sure you do not overlap the arm cord over each other. Install the drum with cord back onto the threaded stem making sure the cord is coming from the bottom of the drum going up to the opposite side pulleys.
It’s very important that the cord is coming out at the bottom of the drum and then wrapping up the opposite pulleys. If the cord is coming out at the top of the drum to the pulleys then it will criss cross over each other and wear the cord out within a couple months.
-
Arm Exerciser Combo: Cord, Drum, Grips
Free Shipping for orders over $50 within the USA
The A/E Combo, includes the cord, drum and two grips.
Fits all original USA built skiers except Plus Series. Will fit ski machines produced from 1976 to 1998
Will not fit an ICON made ski machine which was produced after 1999
-
Arm Exerciser Knob
Free Shipping within the USA
The A/E knob is located on the top of your arm cord drum. If this knob keeps loosening most likely the A/E bearing is worn out or your knob has a hair line crack in it. This knob will only fit the original USA made skiers that were produced from 1976 to 1998.
This knob will not any ICON skier which was made after 1999.
-
Arm Exerciser Resistance Bearing
Free Shipping for orders over $50 within the USA
This bearing is located between the A/E Drum and the A/E drum spring. If your arm tension is slipping you will need to replace the A/E resistance bearing. The definition of A/E is arm exerciser. This A/E bearing will fit any style skier made prior to 1999. The bearing will not fit a ICON skier made after 1999.
-
Arm Exerciser Leather Resistance Pad
Orders under $50 will have a flat $5 shipping rate. If the order exceeds $50 then it is free shipping.
Located under the arm exerciser drum. Pad should be placed in a plastic bag with 3inOne oil for 24 hours before installing. Once this pad becomes blackened you should replace it. Lube pad with 3inOne Oil every couple months. If your skier has two glued on leather pads you will need to get two metal clips to hold this style in place the cost of two metal clips is $17.50. Skiers in the 70's and up to the mid 80's had two glued on pads.
-
Clips for Leather A/E pad
Free Shipping for orders over $50 within the USA
These clips are used to hold the long rectangle leather A/E pad in place. Wood Style Skiers manufactured in the 1970's to the late 1980's had two small square leather pads that were glued on the upright tube.
In the early 1990's NordicTrack updated the two glued on square leather pad design so the leather pad could be replaceable they did this by placing two metal clips that snap onto the arm tube which has nubs on them to hold the newly designed rectangle pad in place.
The price for two metal clips is $17.50
The second detailed photos shows the old style two leather pad design and it also shows the two clips next to the arm tube. The third photo shows the clips installed on the arm tube with the one piece long rectangle pad on top of the clips.
-
Arm Exerciser Round Leather Resistance Pad
Free Shipping for orders over $50 within the USA
This pad fits only the Achiever, Medalist, Elite, Club. Pad should be placed in a plastic bag with 3inOne oil for 24 hours before installing.
This pad is also used on some NordicSport models..
-
Arm Exerciser Drum Spring
Free Shipping for orders over $50 within the USA
Fits all wooden style Skiers. This is the spring that is between the A/E bearing and the A/E knob.
-
A/E Pulley Bushing Set
Free Shipping for orders over $50 within the USA
This bushing is used in the A/E pulley assembly there are two required per skier and are located at each corner of the arm tube. If you do not lubricate your A/E pulley with 3inOne oil every couple months most likely you will wear out this bushing if you have worn out you bushing please add this item to your cart. You will receive two for $3.00
-
Arm Exerciser Grip
Free Shipping for orders over $50 within the USA
Fits all Skiers. This Grip is made of a very hard material it should never rip like the softer grip that NordicTrack produced.
-
Arm Exerciser Resistance Spring
Free Shipping for orders over $50 within the USA
Fits only Achiever, Medalist, Club, and Elite models. This spring was also used as a dragstrap spring for some NordicSport models
-
Arm Exerciser Hip Pad Support Bracket
Free Shipping for orders over $50 within the USA
NordicParts.com is proud that we produce this superior hip pad bracket.
We purchase the raw steel, then have a local Minnesota machine shop cut and weld the steel to fabricate this bracket. The brackets are then sent to our local powder coater for a superior finish. NordicTrack used this design in the 80's, then in the 90's they went with a cheaper cast metal bracket. The cast metal bracket is prone to breaking/snapping whereas the welded steel bracket shouldn't ever break.
Not only is this bracket stronger than the cast style, it is much nicer in appearance and will look amazing on your skier.
Fits all wooden style Skiers, EXCEPT Elite and Challenger model.
-
Extended Arm Exercisor Hip Pad Support Bracket
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
This bracket is designed for people over six feet tall, it has a longer stem and is welded at a different angle. It also has an extra hole that allows a pin to go through to keep the bracket at an angle.
We purchase the raw steel, then have a local Minnesota machine shop cut and weld the steel to fabricate this bracket. The brackets are then sent to our local powder coater for a superior finish. NordicTrack used this design in the 80's, then in the 90's they went with a cheaper cast metal bracket. The cast metal bracket is prone to breaking/snapping whereas the welded steel bracket shouldn't ever break.
Not only is this bracket stronger than the cast style, it is much nicer in appearance and will look amazing on your skier.
This bracket is made from steel square tubing that is welded to flat stock steel, then they are powder coated. The original NordicTrack brackets were made from pot metal and poured into a mold which is a much weaker design.
You will receive one bracket and one pin for $40.00
-
Arm Exerciser Hip Pad
Free Shipping for orders over $50 within the USA
Fits all wooden style Skiers built from 1976 to 1998
-
Upright tube rubber stopper
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
This rubber stopper fits on top of the upright tube to prevent the hippad slider from coming off and to prevent you from hurting yourself on the sharp metal edges of the upright tube.
-
Ski Glide Button Set
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The glide buttons are located on each side of the ski in the center of it. They are used to prevent wood on wood contact.
Glide buttons will wear down to be flush with the ski and once they are flush you should replace them. You should also coat the sides of the skis with paraffin wax which will provide a lubrication for wood on wood contact.
To remove the old glide buttons you will need to use a pick to pick them out. To install them you will need to put one end in first then tap it in at an angle with a hammer you will keep tapping it until you have it all the way in the slot. Then tap it so both ends are even.
The glide buttons will be black in color and are slightly wider than the first generation. The reason for them being wider is for more of a snug fit.
You will receive 4 glide buttons for $13.50
-
Skier Foot Traction Paper
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
Located on top of the skis. Each set includes two sand paper pads. Traction paper is black in color
-
Monitor to upright tube cable
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
This monitor to upright tube cable reaches from the computer to the upright tube. We custom manufactured this cable to be 30.5 inches long. This cable is not coiled we discovered that the coiled cables became stretched after years of use.
-
Ear Clip Pulse Cord
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
Pulse Cord that attaches to your ear. Will not work with the football shaped monitors that were produced in from 1996 to 1998. Will work with all other year and style of monitors.
-
PRO Conversion Kit
Free Shipping for orders over $50 within the USA (Due to the size of this item we cannot ship it outside of the USA.)
If you have a Sequoia, Excel, 505 or Challenger you know that you cannot elevate the front end with this kit you can convert your non elevating skier to be just like a Pro skier. You will have six different levels to adjust the height of your skier. Its very simple to convert your skier it will take about an hour to do the conversion.
This item ONLY ships to USA addresses. If you live outside of the USA please do not purchase this.
-
Machined Flywheel
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The flywheel is a very important component of your skier. If your flywheel is rusty you need to clean it or replace it. If your skier has the black 3/4 inch strip where the dragstrap rides you need to replace it with the machined style flywheel. To see a solid black flywheel and a rusty flywheel look at the pictures on the detailed section. Look at our maintenance section to learn more about your flywheel.
-
Nylon and Steel Washer Set
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The nylon and steel washers are located on each side of the driverollers. There is one nylon washer on each side of driveroller then one steel washer sits next to the nylon washer.
-
Side Board Bearing
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The Side Board Bearing is located at each end of the flywheel axle. Two are required per machine.
If the bearing is stuck in the side board then simply take the flywheel axle and put it back into the side board bearing and move it with force but slowly side to side and the bearing will wiggle it’s way out.
-
U-Bolt
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The U-Bolt Holds the flywheel tight onto the Flywheel Axle
-
Plastic Driveroller Spacer
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
This plastic spacer is used on the flywheel axle to prevent the left driveroller from moving side to side. The spacer comes with a magnet so the electronics can pick up a signal.
-
Flywheel Axle
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
This is the flywheel axle the driverollers ride on. The axles that were produced from 1976 to 1998 are extremally hard and generally never need replacing. In 1999 ICON purchased the name NordicTrack after the original company filed bankruptcy, Icon did not harden the axles to the level that the original NordicTrack company did. If you have an ICON skier you most likely are replacing your flywheel axle every couple years this flywheel axle is much harder and will be nearly impossible to wear out. If you have grooves worn into your old flywheel axle replace it with this one.
-
NordicTrack Flywheel Collar Clamp
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
This collar clamp is used on the flywheel near the driveroller to prevent the driveroller from moving side to side. It has an Allen Head that is used to tighten the collar clamp to the flywheel axle.
-
Upright Frame Tube Snap Button
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
This snap button is used on the inside of the Chrome upright tube that connects to the front frame. When you fold your NordicTrack up the snap button holds the tube into place. This snap button measures 3/8 inch If your NordicTrack came with the 3/8 detent pin this snap button will replace the detent pin.
-
Arm Tube Snap Button
Free Shipping for orders over $50 within the USA
This snap button is used on the inside of the chrome arm tube that connects the arm tube to the hippad slider. This snap button measures 3/8 inch.
-
Hippad Slider Bumpers
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
These Hippad bumpers are located on the inside of the hippad slider, there is one on the front side and one on the back side of the slider they are used to prevent the slider from rocking back and forth. Most people lose these once they take the hippad slider off the upright tube. The cost of two hippad slider bumpers is $12.00
-
Pro Decal Sticker set
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The decal sticker set includes two stickers that were placed on each side of the wooden side board this are for the Pro model. You can also use these on your cars bumper if you want to show your love for your NordicTrack.
-
Tension Control bracket
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The Achiever, Medalist and Elite skiers and a tension control on the right side of the skier to control the leg tension this leg tension control mounted to a bracket. If you need the bracket please add this to your cart
-
Arm tension pointer
Free Shipping for orders over $50 within the USA
Achiever, Medalist, Elite and Club models used this pointer to show you the arm tension. The leather A/E pad mounts on this pointer. The early units did not have the two knubs to hold the round leather A/E pad in place if you have a 1987 to 1988 skier that used a pointer for the arm tension you will need to upgrade to this pointer in order for the leather A/E pad to mount to it.
-
Orginal NordicTrack 1/4 inch detent pin set
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The 1/4 detent pin was used for the leg elevation and also used for the upright tube on skiers manufactured in the 1970's to the early 1990's. The price for two pins is $25.00
-
3/8th Detent Pin with washer
The 3/8th detent pin was used on 1991 to mid 1994 skiers. The 3/8th detent pin is used to hold the upright tube from falling down it connects the upright tube to the front frame. If you skier used a 3/8th snap button this pin will replace the snap button.
Free Shipping for orders over $50 within the USA
-
Front Frame Bumper for Upright Tube
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
Skiers produced from the early 1990's to around 1995 used a 3/8th detent pin or a 3/8th snap button to lower the upright tube from the front frame. This generation of skier was famous for having a wobble in the area where the upright tube meets the front frame. NordicTrack realized this and started installing these rubber bumpers on the inside of the front frame where the upright tube meets it. This bumper will remove the wobble affect that you may experience from that generation of wood style skier.
It attaches by an adhesive on the back side of it that is already installed on it. Just peel the tape and stick.
-
Replacement 1/4 inch detent pin set
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The 1/4 inch detent pin can be used for the leg elevation on the Pro, Achiever, and Medalist wood style skiers produced from 1976 to 1998. It also was used for the upright tube on skiers manufactured in the 1970's to the early 1990's. The price for two pins is $12.00.
These do not have the NordicTrack logo on them but they will work just fine since the pin is the same exact size.
You will receive two 1/4 inch pins for $12.00
-
Front Legs, Pins, Bracket and Bolts
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
If you have moved and have lost your NordicTrack legs, bracket, pins and bolts we have a kit for you. Please add this item to your cart if you have lost your entire front leg assembly.
-
Upright Tube Knob
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
This knob was used on NordicTrack ski machines that were produced from 1995 to 1998. The knob is used on the lower portion of the upright tube and it secures the upright tube to the front frame.
-
Grip 'N' Click NordicTrack Grips
We were going through our warehouse and found a couple dozen of these special grips. These are comfortable grips which are manufactured out of hard contoured plastic. It is recommended to be approximately 8 feet from your TV or VCR.
These were manufactured in 1996 so we are not sure how easy they can be programmed to more modern electronics. The manual states it will work with brands such as Goldstar. GE, Hitachi, JVC, Magnavox, Mitsubishi, NEC, Panasonic, Philips, Pioneer, RCA, Samsung, Sanyo, Sharp, Sony, Toshiba and several other brands. We are not guaranteeing that these will work with your device. We are selling them as comfortable, contoured grips that are now a collector item.
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).