Club 900 Skier
-
![White Foot glide wheel (older style only)]()
White Foot glide wheel (older style only)
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
These wheels are specifically manufactured for NordicParts.com this wheel will fit all the first generation Club 900 skiers with red pin stripes. There are two versions of the red pin stripe NordicTrack Club 900 wheels one type had a spacer built into them which is the black wheel that is pictured and the other style had a spacer separately next to the wheel which is a white wheel. If your Club 900 red pin stripe model had the white wheel that had the spacer separate from the wheel then all you need to do is order the wheel. If your NordicTrack Club 900 wheels are black and have the spacer built into them then you will need to add the bolt and spacer which is an additional $3.00 per wheel.
If you have any questions please call us 612-205-5243 prior to ordering. The price is $20.00 for each wheel and a set of 8 is $160.00 and if you need the spacer and the bolt please choose that in the drop down menu.
-
![Arm Exerciser Cord]()
Arm Exerciser Cord
Free Shipping for orders over $50 within the USA
Cord is 171 inches in length. Fits all wooden style skiers, NordicSport, and Club models. Plus series skiers use a special Kevlar cord, please shop in the plus series section if you have a Plus series.
It is very simple to install the arm cord. You need to untie the cord inside of the grips, or you can cut the old cord, remove the knob, spring, bearing assembly, then lift the drum assembly off the skier, flip it over and unscrew the four screws, then lift the metal plate off. At that point you will see two notches in the drum, pull the old cord out and put the new cord in those notches. Then pull the cord so both ends are even and then put the metal plate back on. You may want to use a little dab of Elmer’s glue on the thread of the screws as this helps them from coming loose. Now wrap one end of the cord 2.5 times to the left and then wrap the other end of the cord 2.5 times to the right. Make sure you do not overlap the arm cord over each other. Install the drum with cord back onto the threaded stem making sure the cord is coming from the bottom of the drum going up to the opposite side pulleys.
It’s very important that the cord is coming out at the bottom of the drum and then wrapping up the opposite pulleys. If the cord is coming out at the top of the drum to the pulleys then it will criss cross over each other and wear the cord out within a couple months.
-
![Arm Exerciser Drum Spring]()
Arm Exerciser Drum Spring
Free Shipping for orders over $50 within the USA
Fits all wooden style Skiers. This is the spring that is between the A/E bearing and the A/E knob.
-
![Arm Exerciser Resistance Spring]()
Arm Exerciser Resistance Spring
Free Shipping for orders over $50 within the USA
Fits only Achiever, Medalist, Club, and Elite models. This spring was also used as a dragstrap spring for some NordicSport models
-
![Arm Exerciser Knob]()
Arm Exerciser Knob
Free Shipping within the USA
The A/E knob is located on the top of your arm cord drum. If this knob keeps loosening most likely the A/E bearing is worn out or your knob has a hair line crack in it. This knob will only fit the original USA made skiers that were produced from 1976 to 1998.
This knob will not any ICON skier which was made after 1999.
-
![Club 900 Arm Exerciser Round Resistance Leather Pad]()
Club 900 Arm Exerciser Round Resistance Leather Pad
Free Shipping for orders over $50 within the USA
Located under the arm exerciser drum
-
![Arm Exerciser Pulley Assembly]()
Arm Exerciser Pulley Assembly
Free Shipping for orders over $50 within the USA
This pulley is located on the top of the arm exerciser. The arm cord wraps around the pulley. The cost is $25.00 for one pulley, one pin, one bushing, and two clips
-
![Club 900 Arm Drum Resistance Bearing]()
Club 900 Arm Drum Resistance Bearing
Free Shipping for orders over $50 within the USA
These Bearings are located inside the Arm Cord Drum. Two are required for Club models. These bearings should be replaced every few years to insure smooth operation for the arm movement.
-
![A/E Pulley Bushing Set]()
A/E Pulley Bushing Set
Free Shipping for orders over $50 within the USA
This bushing is used in the A/E pulley assembly there are two required per skier and are located at each corner of the arm tube. If you do not lubricate your A/E pulley with 3inOne oil every couple months most likely you will wear out this bushing if you have worn out you bushing please add this item to your cart. You will receive two for $3.00
-
![Arm Exerciser Hip Pad]()
Arm Exerciser Hip Pad
Free Shipping for orders over $50 within the USA
Fits all wooden style Skiers built from 1976 to 1998
-
![Toe Strap]()
Toe Strap
Located on top of the skis. The price is 13.50 for one. If you need two please enter 2 as the quantity. The toe straps we manufacture are the strongest style that NordicTrack produced you will never break one of our toe straps.
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
The toe strap will fit any skier made prior to 1999. Does not work with an ICON skier made after 1999.
-
![Arm tension pointer]()
Arm tension pointer
Free Shipping for orders over $50 within the USA
Achiever, Medalist, Elite and Club models used this pointer to show you the arm tension. The leather A/E pad mounts on this pointer. The early units did not have the two knubs to hold the round leather A/E pad in place if you have a 1987 to 1988 skier that used a pointer for the arm tension you will need to upgrade to this pointer in order for the leather A/E pad to mount to it.
-
![Rebuild Service for Club 900 Drive Rollers]()
Rebuild Service for Club 900 Drive Rollers
New drive rollers are not available for the club models. We can rebuild your original drive rollers. Please mail in drive rollers
-
![Grip 'N' Click NordicTrack Grips]()
Grip 'N' Click NordicTrack Grips
We were going through our warehouse and found a couple dozen of these special grips. These are comfortable grips which are manufactured out of hard contoured plastic. It is recommended to be approximately 8 feet from your TV or VCR.
These were manufactured in 1996 so we are not sure how easy they can be programmed to more modern electronics. The manual states it will work with brands such as Goldstar. GE, Hitachi, JVC, Magnavox, Mitsubishi, NEC, Panasonic, Philips, Pioneer, RCA, Samsung, Sanyo, Sharp, Sony, Toshiba and several other brands. We are not guaranteeing that these will work with your device. We are selling them as comfortable, contoured grips that are now a collector item.
Free Shipping for orders over $50 within the USA (Canada and international orders will be charged shipping).
